-Separates USB timeout event processing to a dedicated thread
-Updates USB transfer buffer processor to better detect errors and auto-restart on error (max 3 times)
-Updates Tuner to add an error state and SourceManager to not select tuners with an error state
-Updates ChannelProcessingManager to auto-shutdown channels sourced from tuners set with error state
-Improves logging of USB related errors.
* Initial work on add support for rotating control channels.
* Creates multiple frequency editor control.
* Updates channel source editor to allow user to select multi-frequency
configuration and add multiple frequencies.
* Adds full support for rotating control channels to the P25 channelizer.
Users define multiple frequencies in the channel source configuration.
The decoder monitors the state of the channel for a CONTROL state. If
the state does not stay in the CONTROL state for a user-specified delay
value, then the decoder rotates to the next frequency in the list. This
behavior continues until the decoder state once again changes to CONTROL.
This is NOT a 'scanner' feature.
channel manager so that channel source requests can have a start
timestamp specified and the channel can be preloaded with samples from
the delay buffer. If no timestamp is specified, current time is assumed.
This feature requires corresponding updates to any decoder that wishes
to implement the timestamped sample preloading functionality.
and auto-correction for R820T tuners.
-Updated TunerModel and TunerViewPanel to add 2 new columns to
display the current tuner's PPM setting and (when available) the
measured frequency error averaged over 5 second intervals provided by
certain decoders (e.g. P25 C4FM and LSM). Frequency error value from
P25 decoders is provided from the Costas Loop PLL once 2 or more P25
message sync events have been observed in a short period.
-Updated R820T tuner to auto-correct PPM when measured frequency error
exceeds the +/- 0.4PPM threshold for a period of 30 seconds or more.
Feature can be enabled/disabled by user in the tuner editor panel.
Resolved several issues with P25 C4FM/LSM decoders that was impacting
performance related to channel misalignment from tuner PPM offsets.
that is currently up/down converting the signal of interest, but the
synthesizer is not correctly combining the original two channels.
Some experimentation with the tap count for the channelizer indicates
that we can cut the tap count in half and still have decent decoding
on the P25 decoder when paired to an aligned channelized output. The
2-channel synthesized output decodes partially, but needs more work.
Resolved issue with channel gain in the channelizer that was making the
sample values so small that they were registering as zero when converted
from float to 16-bit int value in the complex wave recorder.
messages and events can be accurately timestamped, and more importantly,
allocated traffic channels can request to be pre-loaded with buffered
samples to ensure that traffic channels don't miss any samples that
are currently missed due processing latency inherent in current buffer
sizing. This should reduce the clipping of starting messages or voice
on the traffic channels.
Restructures processing path for tuner frequency and sample rate change
events. The tuner now embeds these events in the sequence of buffers
that are generated immediately after the event occurs since those are
the buffers that will be impacted by the change. Previously, the change
event would be broadcast throughout the system and would impact any
buffered/cached buffers. This also reduces the number of source event
change listeners that have to be managed. Note: this change is not yet
implemented in all tuners ... only in the TestTuner implementation.
Updates the polyphase channelizer to now buffer channel results and then
dispatch the buffer to the channel output processors to improve efficiency
of using float arrays versus single value complex float processing.
center frequency each time we allocate a new DDC/channel. Adds
support for broadcasting channel count change source events so that the
tuner can accurately convey sourced channel counts via tuner events.
Completes changeover of polyphase channel manager to support arbitrary
bandwidth channels. The new approach provides greater compatibility
across any tuner sample rates. Likewise, all decoders will have to be
updated to adapt to any channel sample rate, although channel bandwidths
will be at least 12.5 kHz and likely no more than 25.0 kHz, with a 2x
oversampling that produces channel sample rates in range 25.0 - 50.0
kHz.
